AEE MagiCam S51 action camera test

Testing a new camera. I have to adjust the mounting angle, it’s too low. Also I put a wrong mic plug and got terrible wind noise. I managed to remove it a bit in post processing.


Posted in Honda FT500 Scrambler, moto!, movie | Leave a comment

so it begun



Posted in Honda FT500 Scrambler, moto! | Leave a comment

Cheetah ladies photo shoot with Ania

DUD_0378 DUD_0387 DUD_0392 DUD_0398 DUD_0399 DUD_0406 DUD_0409

Posted in commercial photography, fixed gear | Leave a comment

Mongolia 2014

IMG_0111 DUD_0252 DUD_0260 DUD_0226 DUD_9949 DUD_0266 DUD_0187_Mars DUD_0167 DUD_0158 DUD_0135 DUD_0120 DUD_0107 DUD_0106 DUD_0098 DUD_0036 DUD_0043 DUD_0074 DUD_0076 DUD_0079 DUD_0088 DUD_0092 DUD_0012 DUD_9960 IMG_0073 IMG_0086 IMG_0090 DUD_0063 DUD_0094 DUD_9980

Posted in moto!, travel | Leave a comment

spring is here, time to hit the spanners

Here’s how the finished product from the last post looks like. Much better than the previous one, now I can pivot the bike on it.

DUD_7631 DUD_7630

After I had ditched the centre stand last year, I got tired of jacking the bike up on pieces of wood every time I wanted to do some serious work on it, and I decided I need a service stand. So I went to the shop buy soma no prescription and bought… some square profiles 30mm x 30mm x 3mm and built one. Doing it I realised that now that I actually can weld a bit, I need to focus on the “keeping things straight and square” side of it. Mainly to have the patience to make jigs etc. I’m always rushing to get to the welding as fast as possible, when in fact it’s more like a finishing touch to all the designing, measuring, cutting, fitting and other 80% of the work necessary to get a good result.


I ended up recutting and rewelding the thing a few times to get it reasonably straight. But it works like a charm!

DUD_7620 DUD_7619

I found a new spot for the crankcase breather and used a much longer tube, hoping that it will prevent it from spitting oil at all the surrounding elements, like the air filter, battery and my trousers.


The final solution to the sticking rear brake was to buy a front calliper off a Honda XL600. It fits the mount right on, the only difference to the original is that the piston is a bit bigger. I might end up with a stronger rear brake, so what. I still have to make an adapter for the Honda CB600 rear master cylinder I’m using, cause it’s misaligned with the pedal brake a bit and causes problems.


You may also notice new rubber at the back. It’s the same as the front, the ever so popular Continental TKC80, in 140 size. I picked it up for 15 EUR, with 7mm thread left and a small damage to the tire bed. It’s no issue here, since I always use an inner tube at the rear.


Being at the arse end of the bike I also did some work on the fender. I cut it shorter and welded a light and plate bracket at the back of it. I also ditched the rubber flap I had there.


DUD_7648 DUD_7639 DUD_7641

In the beginning I wanted to build a retro scrambler out of it, but I realised that with that square mid eighties engine, mag wheels, disc brakes and other details it will never look like it’s from the fifties. Now I want to stick to the sharp lines of that bike and emphasise them even more. I already have a crazy idea for the front light(s) setup, and more important, I don’t give a damn if anybody will like it.

Posted in DIY, Honda FT500 Scrambler, moto! | Leave a comment


Get the Facebook Likebox Slider Pro for WordPress